How to Format Floppy

- Start Windows Explorer, Windows NT Explorer, My Computer.

- Apply the right mouse button to snap the drive containing the floppy disk you wish to format, and then click Data Format on the menu that appears.

- In the Format dialog box, click the choices you want to use to format the disk, and then click Start.

Options that are available:

This will depend on the floppy disk that we are formatting, most discs are now 1.44Mb, it is better to exit this selection as it is.

FAT or NTFS, FAT is the right file system for floppy disks, still if you get a utility set up to enable NTFS floppies so select NTFS, if you are unsure or FAT is the just alternative then just leave it on FAT.

Allocation Unit Size: This should be left on the default option unless you have a cause to change it.

Volume Label: This is where you can enter a label for your floppy disk, just typewrite the name into the box, in our case we have made the disk New Disk.

Quick Format: This selection can be chosen if the disc takes previously been formatted and you only want to loose the data off the disc.

Create an MS-DOS startup disk: This option can be used to copy system files over to produce a bootable system disc .
When you have chose the options that you want merely click on the Start button.

Later snapping Start you will be given a warning informing you that every informations on the floppy disk will be erased, assuming there is no data on the floppy that you require click ok.

Later On clicking OK you will see a advance measure and that will be observed by an alert informing you about the status of the format, i.e. whether it gone prosperous or not.

If you desire to format some other Floppy Disc then insert a other volume label and after that click the Start button in the format dialog box over again.

When complete click Close button.Your floppy disk is formatted and can be used to store your data files.

For more information visit our page how to format a computer

How to format Ms Dos

Just About MS DOS

Microsoft DOS is a control line user interface first presented in 1981 for IBM PC and was last updated in 1994 when MS-DOS 6.22 was published. Although MS-DOS is not commonly used now, the command case applied over Microsoft Windows is. This Page takes full data about MS-DOS and the Windows command note.


Directions to format DOS


Be sure you get a bootable floppy disc or CD.
Insert the disc into the PC, and turn it along. The computer will boot to a black screen showing simply an "A:>" prompt or a prompt indicating the letter of the drive you booted from. You can also accomplish this by booting your computer with the disc in the drive.
Typecast "format c: /s" and hit "Enter." The formatting action will start.
Shot "Y" on the keyboard for "Yes" when asked "Are you positive you wish to erase everything along drive c:," and then press out "Enter."
Remove the disc, and reboot your computer. It will boot to the "C:>" prompt from the hard disc.
More information about anything you need how to format a computer

How to format hard:95 98 ME

For formatting hard Windows, you will take a Startup Floppy Disk and a Windows Installing CD Note: We recommend applying the Startup Diskette.

Once you get your Startup Diskette, enter it into the floppy drive and reboot the PC.

Choose option #1 - Start the PC with CD-ROM backup.

After a minute or so, you will see "A:>_".

Typecast "fdisk" and press out Enter.

If asked to enable important disc backup, Select Y for Yes. (Note: Some versions of Windows 95 may not be harmonious with big disc backup. Select N here if it does not backup the FAT32 file system.)

Choose Option #1 - Make DOS partition or Logical DOS Drive.

Select Option #1 - Make Primary DOS Partition.

The drive wholeness will be verified.
Unless you are planning to take multiple partitions, Select Y when required if you desire to use the maximal free size for the partition and to make the partition effective.

The drive integrity will be verified again.

When complete urge the Esc key to exit fdisk.
Without removing the floppy disk, press out the reset button on the PC or press out the keys Ctrl then Alt then Delete and loose them together. This will restart the PC.

Over Again, Select the alternative to Start the PC with CD-ROM backup.
When you mark A:>, instantly above it is a content about your CD-ROM drive. It will state you the letter specified to your CD-ROM drive, take line of it.

At the A:>, typewrite "format C:" and press Enter.

Press out the Y key then the enter key when required if you want to carry on with the HDformat.
It will take several minutes to format the hard drive.
You will be asked to pick out a Volume Label, which is a name for your hard drive. It gets no result on the operation of your computer, you may pick whatever name you want.

For more info. visit our page How to format a computer

How to format Drive C

Formatting drive C: is complete with a a few mouse clicks using the Disk Managment of Win 2000 or Win. XpThe option "format" still is grey for the drive C: or wherever Windows itself is placed. This choice is deactivated because the system does not allow to pass over itself off the drive.
If you want to format this drive nonetheless, apply this style:
Put the installation XP CD or Windows 2000 into the CD drive gathering and start the computer over again. It should shortly say "Press a key to start from CD".
If not, you have to change the boot sequence in the computer´s BIOS. Other choice is to use a special role key which points a boot computer menu where you can chose the CD drive, if offered. The most common keys for this are [F12] and [Esc].

With the first screen of the setup program select "R" to enable the repair mode. The following screen allows you to choose a Windows installation for repair and requires for its admin password afterwards .

Directly you take a command line user interface. Enter "map" here and you will get an overview of all partitions and their corresponding drive letter.
If you had sure which drive you want to format, typewrite the command "format", followed by the drive letter like

Format C:

The system will then format the drive with the identical file system typewrite that the drive already has. Applying the parameter "/fs:" you can pick out a file system. If for example you wish to format drive C: with NTFS you enter

format C: /fs:ntfs

To leave the console, type exit.
For more information visit our page How to format

how to format hard on XP

To format hard disc drive with Windows XP or 2000, put in XP CD and reboot your computer.
Your PC should automatically reboot from the CD to the Windows XP Setup Main Menu.
At the Welcome to Setup page, press ENTER.
Press F8 to receive the Windows XP Licensing Agreement.
If an existing Windows XP installation is noticed, you are prompted to fix it. To bypass the repair, press ESC.
Role the ARROW keys to select the partition or the unpartitioned space where you want to create a different partition. Press Out D to delete an active partition, or push C to create a other partition.
Typecast the size in MB that you want to role for the other partition, and so press out ENTER, or just press ENTER to create the partition with the maximum size.
Take the format choice that you want to use for the partition (Recommended: NTFS), and then press out ENTER.
After the Windows XP setup program data formats the partition, follow the instructions that appear on the screen to proceed installing Windows.
For more instuructions visit our page How to format Hard on Windows XP 95 98 2000

How to reformat

Usefull info: I found a site with detailed step by step info on how to reformat a computer